Everything you need for a complete photovoltaic system — with price per Wp shown, 21% VAT included and prices transparently computed server-side.
It supports the panels on a sheet metal roof without loading it: a 4.8 m aluminium profile that weighs about 3.1 kg and raises the modules by only 22.5 mm.
It prevents the rail from migrating on the roof: a fixed point that locks the BasicRail 22 bar and splits the expansion towards both ends. K2 BasicLock 22 set, code 1003558.
It joins two rails end to end so that you get a continuous row, without cutting bars. Aluminium and A2 stainless steel, 3 fixing holes, Torx T25 screws included.
Lifts the panels off the rail so air can circulate underneath: cooler modules lose less power, and there is room for microinverters below. K2 RailUp set, code 2003191.
It fastens the rail directly to the sheet corrugations, without metal-on-metal contact: glass-fibre reinforced polyamide, UV resistant, 2 screws 6x38 per clamp.
Roof hook with adjustment in two directions, so that the rail comes out straight even if the roof covering is not flat; variant from the range marked angle 150.
It anchors the entire panel system into the roof truss, on tile roofs: height-adjustable hook, with an interface for H-type aluminium profile.
Roof hook for tiles, with a base plate adjustable to 3 heights, so that the tile above sits freely and does not crack under snow load.
A car shelter and a panel support at the same time: self-supporting structure of anti-corrosion steel, with room for 9 panels tilted at 10 degrees to the south. The panels are not included.
You shade two parking spaces and gain room for 15 panels: self-supporting structure of anti-corrosion steel, 10 degree tilt facing south. Panels are not included.
Closes the row of panels: it presses straight on the module frame at the edge, without twisting it. Versions for frames of 30, 35 and 40 mm or universal, with M8 bolt.
Fixes the panel at the end of the row, with adjustment for frames of 32-42 mm, therefore for any common panel. Set of 4 pieces in silver aluminium, 0,29 kg.
It holds the panel at the end of the row, where the wind pulls hardest: aluminium end clamp, quick Click fixing, for H-type profile 40x40 mm.
A single clamp for almost any panel: it grips frames of 30-42 mm and fixes two neighbouring modules simultaneously on the SingleRail, SolidRail and BaseRail rails.
It grips two adjacent panels at once, with a click system that holds the clamp open during installation. Set of 6, fixes 4 modules, adjustment 32-42 mm, silver aluminium, 0.38 kg.
A single part holds two neighbouring panels and keeps the correct gap between them: aluminium mid clamp, Click fastening, for H-type profile 40x40 mm.
Fastens the panels on a standing seam sheet roof without any hole in the roofing: it is tightened with bolts directly on the seam. Stainless steel body, adjustment slot, M8 threaded joint towards the rail.
It grips two adjacent panels in a single tightening and keeps their expansion gap, usually 18-22 mm. It is fixed with an M8 bolt in the rail channel.
Keeps the cables tight on the structure so that they do not chafe against the sheet metal in the wind. Outdoor cable tie, 200 x 4,6 mm, with the possibility of chaining for thick bundles.
Joins two mounting rails end to end, so that the row of panels can be as long as needed. 0.14 kg per piece, 60 pcs/box, for SM 30x50, SM 31x50 and SM 40x80 profiles.
You join two rails end to end and obtain a single, continuous one: aluminium connector for H-type profiles, fixed with screws, usually M10.
Joins two rail bars end to end, so you can obtain rows longer than the standard bar and also use the leftover ends, with less material waste.
Raises the lower edge of the panel on the flat roof, at a fixed tilt of 10 degrees. Aluminium, only 0,085 kg/piece, K2 code 2003243.
The rear support that raises the panel to 10 degrees on the flat roof; it clips in or is fastened with a screw, 0.3 kg/piece, K2 code 2004125.
